Gate Repair in Kennedale - Same-Day Repair, Priced Before We Start

Fast, Reliable Gate Repair Across Kennedale

Gate repair in Kennedale runs $180-$450 for most hinge, post, and realignment work, while electric gate and opener repairs typically land between $240-$680 depending on the motor and board. We dispatch from our Dallas-Fort Worth office and reach most of ZIP 76060 the same day you call, because we keep crews scheduled around Kennedale’s acreage properties and shared driveways. If your gate is dragging, binding, or dead on the post, call (469) 564-8046 and you’ll get a live person, not a voicemail tree. Ironworks Gate Co. has been fixing gates right for over 42 years, and a written 90-Day Done Right Promise backs every job we finish in Kennedale.

Call (469) 564-8046

Why Ironworks Gate Co. Is Kennedale’s Preferred Gate Repair Company

Kennedale is not Arlington. It is not Mansfield. It is a semi-rural pocket inside the metroplex where driveways are long, lots are big, and the gate at the road is more likely a 16-foot welded pipe swing than a decorative suburban insert. Homeowners here call us because we know the difference before we ever pull onto the property. We work on heavy acreage gates, pasture entrances, shared driveways off Mansfield Cardinal Road, and narrow rights of way where a swing gate simply cannot be built to clear a vehicle.

Victor Salinas leads our crews, and the standard he holds is the same on a $200 hinge repair as on a $6,000 automation job: fix the root cause, not the symptom. Around Kennedale, that usually means the soil. Blackland Prairie clay swells and shrinks with every rain-drought cycle, and a gate post set in 18 inches of concrete will lean within two seasons. We rebuild those footings below the active clay zone at 24 to 30 inches, so the post stays plumb through the next wet winter. That is not a patch. It is the repair standard this ground requires.

Our Gate Repair Services in Kennedale

Electric Gate Repair

When an opener on a Kennedale driveway stops responding, the problem is rarely the motor alone. It is usually the load. Heavy pipe-frame gates that have dropped even an inch put constant torque on the operator arm, which burns out circuit boards and strips nylon rollers faster than any normal wear. We test the full system under load, not just the fault code. If the board is dead, we carry replacements for DoorKing, Elite, Ghost Controls, and Mighty Mule, so most jobs are done in one visit.

Automatic Gate Repair

Automatic slide gates catch hell on unpaved Kennedale driveways. Caliche dust and clay silt collect in the rack and pinion track, and a 105°F afternoon makes the motor labor until it overheats or trips thermal protection. We clean the track, reset the drive gear clearance, and check the ground rail for buried debris that causes the jerking motion owners describe as a “grinding and stuttering” gate. Then we verify the safety edges and entrapment loop so the gate complies with the current UL 325 standard before we leave.

Hinge & Post Repair

This is the defining repair in Kennedale. A homeowner near New Hope Road called us after spring rains left his 16-foot pipe-frame swing gate dragging across the caliche. The hinge post had tilted outward maybe four degrees, enough to drop the latch side three inches. We cut and re-welded the post into a new 30-inch footing below the clay heave line, replaced the sagging pins with greaseable ones, and the gate swung clear. The previous fix, done by a handyman two years earlier, had simply re-set the same post at the same shallow depth. That is why he called us.

Gate Realignment

A gate that will not latch, rubs the post, or sags at the far end is a geometry problem. On Kennedale’s unlevel acreage, we see gates installed on a slight grade that gradually rack out of square as the soil shifts. Realignment means checking the post plumb in both planes, shimming or re-welding hinges as needed, and adjusting the drop rod or cane bolt. It is not about forcing the gate back into place with a jack; it is about restoring the original travel arc so the gate closes without fighting.

Trusted Brands We Service in Kennedale

We carry parts and diagnostic tools for nine gate-automation brands, including DoorKing, Ghost Controls, Elite, and Mighty Mule, the units we see most on Kennedale acreage and suburban installations. That matters because a tech who only knows one brand will replace what is bad rather than fix what is wrong. Trained on all nine, we make the correct fix on the first visit, whether the opener on your post is thirty years old or installed last spring. Parts we don’t have in the truck arrive from our supplier within a day, and we return to finish the job without a second service fee.

Common Gate Repair Problems We See in Kennedale Homes

• Clay heave tipping shallow-set posts. Blackland Prairie soil expands and contracts so aggressively that any post set less than 24 inches deep will lean within one to two wet seasons. We rebuild below the active zone, not just straighten and hope.
• DIY pipe gates racking out of plumb. Many acreage owners weld their own gates to save money. The welds hold. The footings don’t. After a wet winter, the gate binds the operator and strips rollers.
• Clay silt jamming slide-gate tracks. Unpaved shared driveways shed fine dust and silt into the rack and pinion. Over a dry summer, that packed clay makes the gate jerk and the motor overheat.
• Heat-stressed operator electronics. Board failures spike in July and August across Kennedale. Direct sun on a metal control box can push internal temperatures past design limits, and solar-charged battery banks degrade faster in the heat.

Pricing for Gate Repair in Kennedale, TX

We Also Serve Cities Near Kennedale

Our crews cover Kennedale and the surrounding metro, including Arlington, Mansfield, Fort Worth, and Burleson. See our Gate Repair service hub for full details on what we fix, or Kennedale for local specifics. Same team, same written guarantee, wherever your gate stands.

FAQs - Gate Repair in Kennedale