Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Everman
Gate access control in Everman usually means one of three things: a keypad that has stopped accepting the code, an old operator that will not talk to a new remote, or a gate that binds against the post so hard the latch never lines up. We fix all three, and we do most Everman jobs in a single visit. Our crews know the 76140 streets, the ranch-style homes off W Enon Avenue, and the way Houston Black clay moves a gate post a little more every wet season. Call (469) 564-8046 and a live person answers, day or night.
Most Everman homes were built in the 1960s and 1970s. Their gates were not. Not the way we would build them now, anyway. Posts got set 18 to 24 inches deep with a bag or two of concrete, and the operators were basic chain-drive units that were never wired for modern safety edges or photocells. The access control side was a keypad, maybe a mechanical code box, and that was it. Now those systems are 40 or 50 years old. The electronics are obsolete, the wiring has been pulled and chafed by clay movement, and the post has leaned far enough that the gate will not stay latched no matter how many times the code is entered. That is the real story behind most access control calls in Everman. We will tell you the truth about whether your system can be retrofitted or whether replacement is the cheaper answer.
Why Ironworks Gate Co. Is Everman’s Preferred Gate Access Control Company
We have been working on gates since 1984, and we are trained on nine gate automation brands, including DoorKing, Elite, and Ghost Controls. That matters in Everman because we see a lot of older equipment. A technician who only knows one brand will try to sell you what he stocks. We diagnose what you actually have and give you a straight answer about the least expensive way to make it work reliably.
Victor Salinas leads our crew, and he has spent years watching how Blackland Prairie clay undermines gate installations across Tarrant County. When a keypad will not latch a gate in Everman, Victor’s first question is never “which keypad do you want to buy.” It is “when did the post start leaning.” That local knowledge is the difference between a repair that lasts and a new keypad that quits in six months because the gate still will not close.
We do not use answering services. When you call (469) 564-8046, you get a person. And when we give you a price, it is the price. The quote is agreed before any work starts, and it is written down. Every job we complete in Everman is protected by our 90-Day Done Right Promise: if it is not right, we come back and make it right. No paperwork, no arguing.
Our technicians are background-checked, uniformed, and they work in your driveway the way they would work at their own mother’s house. Dispatch and scheduling are coordinated from our Dallas-Fort Worth office, and crews serve Everman locally. When you call, you will not be routed through three departments. You will get an answer and a plan.
Our Gate Access Control Services in Everman
Keypad Entry
A keypad on an Everman gate from the 1970s or 1980s is usually a simple mechanical or early digital unit that has outlived every replacement part source. When it fails, the fix is a modern keypad wired into the existing operator, provided the operator itself is sound. If the post has shifted and the gate will not physically close, the keypad cannot fix that. On a ranch-style home off W Enon Avenue, we found a chain-link swing gate that would not latch because the hinge post had leaned two inches toward the latch post. The homeowner thought the keypad was dead. Our crew cut out the old shallow footing, reset the post in a 36-inch-deep concrete pier, and then reinstalled the existing LiftMaster keypad entry so it finally held alignment. In Everman, that is a typical order of operations: post first, electronics second.
Card Reader
Card readers make sense for Everman residents who want a simple, durable access point without handing out codes to every family member, landscaper, or pool service. We install proximity card readers and key fob systems wired into your existing operator. The important detail on older Everman gates is the wiring. When the gate post shifts, it pulls the underground conduit and can chafe the low-voltage wire until it grounds out in wet clay. We check the conduit run and the connections before mounting any new reader, because a reader bolted to a moving post will never stay aligned.
Smart Access
Smart access means controlling your gate from an app on your phone, usually through a Wi-Fi or cellular bridge module added to your existing opener. It works well on Everman homes with solid Wi-Fi coverage at the gate, which varies depending on where the driveway sits relative to the house. We will test the signal strength before quoting a smart module, because a module that loses connection every afternoon when the temperature spikes is not an upgrade. For most Everman properties, a cellular bridge is the more reliable option, and we can integrate it with DoorKing, Elite, and Ghost Controls systems, among others.
Phone Entry
Old phone entry systems from the 1990s are common in Everman, and they are obsolete in a practical sense. Most use landline connections or outdated cellular modems that no longer function. The good news is that the existing keypad housing and wiring can often be reused with a modern cellular or IP-based entry unit. We have upgraded several Everman gates from vintage phone entry to app-based calling without replacing the gate or the operator. If the wiring was pulled by post movement, we will tell you before quoting the upgrade.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Everman
We are certified to service nine gate automation brands, and in Everman we see a lot of DoorKing, Elite, and Ghost Controls equipment, plus the occasional Mighty Mule on a chain-link gate. We keep common control boards, receivers, and safety components in stock, which means most Everman access control repairs do not wait on a part shipped from California. If your operator is a brand we do not stock, we can usually source the board within a couple of days. We will never quote a repair we cannot stand behind.
Common Gate Access Control Problems We See in Everman Homes
- Post movement defeats the latch. Everman’s Houston Black clay expands and contracts with every Texas wet-dry cycle. A post set 18 to 24 inches deep in 1975 has probably leaned enough that the access control strike plate no longer lines up with the latch. The keypad beeps, the operator hums, but the gate will not secure. The fix starts underground, not in the keypad.
- Obsolete control boards trip and loop. Original 1970s and 1980s operators on chain-link gates were never wired for modern UL 325 safety photocells. When the old control board fails, it can get stuck in an open-loop condition where the gate opens halfway and stops. A new board with proper safety edges is the safe answer, and it can usually be retrofitted into the existing operator housing.
- Chafed wiring in shifting ground. Decades of clay heave pull hinge posts away from underground conduit runs. The low-voltage wiring to your keypad or card reader can chafe through its insulation and short out in wet clay. What looks like a dead keypad is often a wire grounding out three feet underground.
- Summer heat stress on older components. Temperatures above 100°F are normal in an Everman summer. Heat accelerates rust on unpainted steel components and cooks the capacitors in aging control boards. A board that works fine all winter may fail in July. When we see heat-related failures, we replace the board and confirm the housing has proper ventilation.
Pricing for Gate Access Control in Everman, TX
A keypad replacement on an existing Everman gate typically runs $280 to $450 installed, depending on the wiring condition and whether the post alignment needs correction. A proximity card reader system for a single gate runs $400 to $700 with two fobs included. A smart access upgrade with a cellular bridge runs $350 to $650 on top of the existing operator, including app setup and testing. An old phone entry system replacement with a modern cellular unit runs $500 to $900 depending on the existing wiring and whether a new post box is required.
| Access Control Service in Everman | Typical Price Range |
|---|---|
| Keypad entry replacement (installed) | $280 - $450 |
| Card reader system with 2 fobs | $400 - $700 |
| Smart access (cellular bridge + app) | $350 - $650 |
| Phone entry system replacement | $500 - $900 |
| Post reset/re-plumb (per post) | $250 - $500 |
If the post has moved and the gate will not latch, add $250 to $500 per post for a reset in a deeper footing. That is the single most common additional line item on Everman access control jobs, and it is the one that makes the difference between a repair that holds and a keypad that fails again next wet season. We quote the full price before any work starts, and we honor it. Call (469) 564-8046 for a free estimate, and ask about our $50 off any repair over $250.
We Also Serve Cities Near Everman
Our Gate Access Control team serves Everman and the surrounding Tarrant County communities, including Burleson, Alvarado, Crowley, and Joshua. If you live outside Everman but within reach of our crews, call (469) 564-8046 and we will get you scheduled. We approach every Gate Access Control in Everman job the same way: diagnose first, quote in writing, and stand behind the work.
Serving Everman, TX - Our Local Coverage Area
We’re based in the Everman area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Everman
The keypad is likely fine. After heavy rain, Everman’s Houston Black clay swells and pushes against your gate posts, throwing the frame out of plumb. The latch no longer meets the strike plate, so the operator unlocks the gate but the gate itself cannot swing free. The real fix is resetting the post in a deeper footing, not replacing the keypad. Call (469) 564-8046 and we will check the post alignment before quoting any electronics work.
In most cases, the gate itself can stay. The question is the post and the operator. If the steel frame is structurally sound and the hinge post can be reset in a deeper concrete pier, we can install a modern keypad, card reader, or smart access module into the existing gate. If the post has broken, or the gate frame is rusted through at the hinge stile, replacement is often the cheaper long-term answer. We will show you the numbers for both options before you commit to anything.
Yes. The old phone entry housing can usually be replaced with a modern cellular bridge and app-based calling system without replacing the operator or the gate. The key variable is the condition of the wiring run and whether the post has moved enough to pull the conduit. We will test the wiring and signal strength before quoting the upgrade.
The hinges are fine. The post is moving. Everman sits on Houston Black clay, which shrinks dramatically during dry Texas summers and swells after heavy rain. A chain-link gate post set 18 to 24 inches deep in the 1970s is too shallow to resist that movement. It leans, the frame twists, and the gate binds. The fix is re-setting the post in a 36-inch-deep concrete pier, and then re-aligning the hinges and latch. We do this work regularly across Everman, and we guarantee it in writing.
You have two realistic options. One is to add a low-voltage gate opener to the existing swinging gate, then install the card reader to control it. The other is to install a standalone maglock system that keeps the gate closed and releases when a valid card is presented, which works if you do not need the gate to swing open automatically. On most Everman properties, adding a swing gate operator is the more practical route, and we can quote both. Call (469) 564-8046 and we will walk the property, test the post alignment, and give you a written number.
Call Ironworks Gate Co. for Gate Access Control in Everman
If your Everman gate is not opening, not latching, or not talking to your keypad, call us first. We are reachable 24 hours a day at (469) 564-8046. A live person answers. We will ask a few questions, tell you honestly whether the problem is electrical or underground, and quote you a fair price before any work begins. We have been doing this since 1984, and we plan to be doing it in Everman for another forty years. Done right, and backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Everman and the surrounding Tarrant County communities.