Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Access Control Across Benbrook
Gate access control in Benbrook usually means one of three things: a keypad that has stopped accepting codes, an older operator that no longer talks to its remotes, or a homeowner who wants to stop climbing out of the truck to open a gate by hand. Most calls in Benbrook are resolved in a single visit, and a typical keypad or receiver repair runs $185 to $340 depending on whether we are replacing a board or the whole entry device. We dispatch from our Dallas-Fort Worth office, and our crews know Benbrook’s streets: the older subdivisions off FM 2871, the acreage lots along Winscott Road, and the lakeside properties near Benbrook Lake where gates work harder than anywhere else in the city. Call (469) 564-8046 and a live person answers, day or night.
Why Ironworks Gate Co. Is Benbrook’s Preferred Gate Access Control Company
We have spent over 42 years working on gates that generalist handymen walk away from. In Benbrook, that means gates with a lot of years on them: ranch-style homes built between the late 1960s and early 1990s, original tubular steel or wrought-iron frames, and operators that were installed when a phone line was still considered high-tech access control. Our technicians are background-checked and uniformed, and they work under a simple code: Krafted right, Every time, Your home first, Standing behind it. The 400th job gets the same care as the first.
Benbrook homeowners call us because the gate has usually been there for decades and the last repair did not last. Victor Salinas runs our crews, and he has seen every failure mode that North Texas clay and lake wind can produce. We quote a flat price before any work starts. No surprises on the bill, no arguing about what was agreed. And every completed job is covered by our written 90-Day Done Right Promise. If it is not right, we come back and make it right. That is the deal, in writing, every time.
Our Gate Access Control Services in Benbrook
We handle the full scope of gate access control: repair, retrofit, and new installation. Here is what that looks like on the ground in Benbrook.
Keypad Entry
Older Benbrook homes often have keypads that are ten or fifteen years old, with faded buttons and corroded battery terminals. Sometimes the keypad is fine and the receiver board inside the operator has failed. We diagnose which one it is before recommending a replacement, because swapping a good keypad for a new one does not fix a dead receiver. Typical keypad replacement in Benbrook runs $140 to $260, including the part and the programming.
Remote Control
Remotes fail in predictable ways: worn buttons, dead batteries, or a receiver that has drifted off frequency. But on Benbrook’s lakeside properties, we also see remotes that work fine from the driveway but fail from inside a truck with a boat trailer behind it, usually because the receiver antenna is corroded or mounted too low. We replace remotes, reprogram rolling-code security, and relocate antennas where they actually reach. A standard remote add-on or replacement runs $75 to $185 installed.
Phone Entry
Phone entry systems let a gate call your cell phone when a visitor presses the button, and they are common on Benbrook acreage where the gate sits too far from the house for an intercom wire. We install and repair GSM-based entry units that work off cellular signal rather than a landline, which matters on lots where the old phone line was cut years ago. A phone entry retrofit typically runs $450 to $900 depending on the hardware and whether we run a new antenna line.
Card Reader
Card readers are the quiet workhorse of access control, and we see them on Benbrook properties where a homeowner wants a few family members or a caretaker to have individual credentials without handing out a shared code. We install and repair proximity readers and key fob systems, and we can integrate them with most major operator brands. A single-card reader setup ordinarily runs $300 to $600 installed, including programming two credentials.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Benbrook
Our Gate Access Control team is trained and equipped on nine major automation brands, and in Benbrook we most often see DoorKing, Mighty Mule, and Ghost Controls on older residential gates. We stock common boards, receivers, and remotes for those brands, which means we are not waiting on a part from a distributor in Houston while your gate stays open. When an obsolete board cannot be sourced at all, we retrofit to a current LiftMaster or BFT board with matching safety inputs, so the gate operator meets current standards rather than limping along on a part nobody makes anymore.
Common Gate Access Control Problems We See in Benbrook Homes
- Clay heave under post footings. Benbrook’s expansive clay shrinks in summer and swells after rain, tilting gate posts a few degrees at a time. A gate that only binds in August and swings fine in February is almost always a soil movement problem, not a hinge problem.
- Lake-wind corrosion on hardware and receivers. Prevailing south and southwest winds off Benbrook Lake carry moisture and accelerate rust on exposed hinges, bolts, and antenna connections. We routinely find receiver boards with green corrosion on the terminals, which is why remotes work only at ten feet.
- Racked boat-trailer gates. Wide secondary gates built for boat trailers carry more load than they were designed for, and repeated cycles twist the frame until the safety photocell misaligns and the gate reverses mid-cycle for no apparent reason.
- Legacy control boards from the 1980s and 90s. Original operator boards fail from surge damage or simply age out. When the original board is no longer manufactured, we retrofit a current board with matching safety inputs instead of patching a 35-year-old circuit that will fail again in six months.
Pricing for Gate Access Control in Benbrook, TX
A keypad replacement in Benbrook typically runs $140 to $260. A remote add-on or replacement runs $75 to $185. A phone entry retrofit runs $450 to $900. A card reader setup runs $300 to $600. If the operator board itself has failed, expect $280 to $520 for a retrofit board and the labor to program it. These are flat, quoted prices agreed before a single bolt is turned, not hourly estimates that drift upward. If the job requires new post footings or commercial-grade weld-on hinges, we will tell you that during the quote and show you the line item. Call (469) 564-8046 for a free estimate. We also offer $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% senior and veteran discount.
We Also Serve Cities Near Benbrook
Our crews cover Benbrook and the surrounding communities, including Benbrook lakefront properties, Burleson, Alvarado, Crowley, and Joshua. If your property sits across the county line or along the south edge of the lake, call (469) 564-8046 and we will tell you straight whether we can be there the same day.
Serving Benbrook, TX - Our Local Coverage Area
We’re based in the Benbrook area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Access Control in Benbrook
Usually, yes. A sagging gate is most often a worn hinge or a tilted post, and both can be repaired without replacing the gate panel. In Benbrook, we frequently find that clay heave has shifted the post footing, so the real fix involves cutting out the old footing, pouring a deeper concrete pier, and welding on heavier hinges. Call (469) 564-8046 and we will tell you what the gate actually needs before quoting any replacement.
It probably does not. Operators manufactured before the mid-1990s often lack the non-contact safety sensors and obstruction-reversal features that current standards require. We can retrofit a modern LiftMaster or BFT board with matching safety inputs onto many older mechanical operators, which is usually cheaper than a full operator replacement. Call (469) 564-8046 and we will assess what your old operator can and cannot accept.
That pattern is a classic sign of expansive clay soil under the gate post footing. Benbrook’s clay shrinks during dry summer heat, causing the post to lean slightly and the gate to bind or drag. After rain, the clay swells and the gate levels out. The permanent fix is a deeper concrete pier that extends below the active shrink-swell zone, which we pour on a regular basis for Benbrook homeowners.
Yes. Most LiftMaster operators from the last 25 years accept a keypad through the same receiver input as the remote, and we can hardwire or program one to your existing board even if the original keypad port was never used. If your board is too old, we retrofit a current receiver so the keypad integrates cleanly. Call (469) 564-8046 for a quote on the keypad and the programming.
For Benbrook lake-shore properties with wide secondary gates, we spec commercial-grade weld-on hinges rather than bolt-on residential units, because repeated trailer loads rack and twist standard hardware until the gate frame deforms. We also pour post footings deep enough to ride out clay movement, and we rebalance the operator so the gate cycles clean even with a full trailer behind the truck. Call (469) 564-8046 for a free assessment.
If you are in Benbrook and your gate will not open, will not close, or will not talk to its remote, call (469) 564-8046. A live person answers, 24 hours a day, seven days a week. We will give you a straight answer and a flat price before any work begins.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Benbrook with gate access control, repair, and installation.