Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Benbrook
Gate motor repair in Benbrook usually costs $240-$520, depending on whether we’re replacing a control board or rebuilding a post footing. Most motor repairs here take one visit, and a live person answers our phone at (469) 564-8046 around the clock. We’ve worked gates throughout Benbrook for over 42 years as a company, and the soil under this city changes the job. A gate that won’t open on Winscott Road is rarely the same fix as one off Timber Creek Drive.
That’s why our Gate Motor & Opener crews carry welding rigs, concrete tools, and motor parts on every Benbrook call. The operator is only half the story. The footing, the hinge post, the rack alignment, and the wind load all decide whether a repair lasts three months or fifteen years. We’d rather fix it once.
Why Ironworks Gate Co. Is Benbrook’s Preferred Gate Motor & Opener Company
Benbrook homeowners don’t call a gate company often. They call once every ten or fifteen years, when a motor finally gives out or a gate starts dragging after a hard summer. That means the company they call matters more than the price on the invoice. We understand that. Most of our Benbrook customers have lived in their homes since the 1980s or 1990s, and many remember the last contractor who took their money and stopped answering the phone.
We do things differently. Every Benbrook job, from a simple motor swap to a full slide gate rebuild, carries our written 90-Day Done Right Promise. If something isn’t right, we come back and make it right. No paperwork, no arguing. Our technicians are background-checked and uniformed, and they treat your driveway the way they’d treat their own mother’s. Victor Salinas, who leads our crews, has spent years diagnosing gate failures across the metro area, and he’s the first to say that Benbrook’s clay soil creates problems most technicians never learn to spot.
When you call (469) 564-8046, a live person picks up. Not a voicemail tree, not an answering service. That matters at 7 a.m. when your gate won’t open and your car is stuck in the driveway.
Our Gate Motor & Opener Services in Benbrook
We focus on four areas that cover the majority of Benbrook gate problems, from Benbrook Gate Repair to full installation services. Each one starts with a free estimate and a written price before any work begins.
Motor Repair
The most common call we receive from Benbrook is a motor that runs but won’t move the gate, or a gate that stops halfway. On older ranch-style properties around Timber Creek and Whitestone, we often find the motor itself is fine. It’s the post that moved. The expansive clay under Benbrook swells after spring rains and shrinks through July and August, tilting posts just enough to bind the gate. We fix the root cause first, then address the motor.
A typical motor repair in Benbrook runs $240-$380 when the issue is a control board, capacitor, or limit switch. If the failure traces to foundation movement, the repair may include footing work and runs higher.
Motor Installation
Gate Installation in Benbrook for a new motor starts around $900 for a standard residential swing gate operator and run up to $2,400 or more for a heavy slide gate unit on acreage. If you’re replacing a 30-year-old operator on a gate that’s also sagging, we’ll tell you. Installing a new motor on a compromised frame just burns out the new motor faster. We quote the whole job up front, including any post work, so the price on the estimate is the price on the bill.
Linear Motor
Linear arm operators are common on Benbrook’s established subdivisions where gates sit close to the house. If a linear motor is grinding or the arm won’t extend fully, the problem is usually either a stripped gear or a gate that’s too heavy for the unit. We see this often on homes near the Benbrook Lake corridor where homeowners replaced an original gate with something heavier. We stock Linear parts and can typically repair or replace a linear motor in one visit.
Slide Motor
Slide gates are the workhorses of Benbrook’s acreage properties and lake-adjacent lots. They carry wide boat trailers, horse trailers, and farm equipment. The south and southwest winds that funnel across Benbrook Lake push hard against these gates, and single-post cantilever installations take the brunt. We service slide motors regularly off Winscott Road, in the subdivisions around the city’s southern edge, and out toward the Johnson County line. A typical slide motor replacement runs $1,200-$2,800 depending on gate weight and whether rack replacement is needed.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Benbrook
Our Benbrook trucks are stocked for the three brands we see most in this area: Ghost Controls on newer residential installs, DoorKing on commercial and estate gates, and Elite on mid-range swing and slide systems. We also service Viking and Mighty Mule units regularly. Because we keep common parts for these brands on the truck, we can usually complete a repair without ordering parts and scheduling a second trip. If you have an older operator and aren’t sure what brand it is, call us. We’ll identify it and give you a straight answer on whether it’s worth repairing or replacing.
Common Gate Motor & Opener Problems We See in Benbrook Homes
- Post movement from clay soil. Benbrook’s expansive clay shrinks and heaves with every wet-dry cycle. When a post tilts even half an inch, the gate binds and the motor strains. We’ve seen motors burn out in eighteen months on a gate that had a perfectly good operator but a failing footing.
- Wind load on slide gates near the lake. Properties along the Benbrook Lake shoreline catch steady south and southwest winds. Single-post cantilever slide gates flex under that load, and the rack and pinion wear out early. We spec heavier hardware for lake-area gates than we would for a shaded lot off I-20.
- Boat-trailer gate hinge rotation. Wide secondary gates built for boat-trailer clearance see high cycle counts and heavy loads. The hinge posts rotate over time, which strips operator gears and throws the gate out of alignment. We use weld-on commercial hinges for these jobs, not bolt-on residential units.
- Outdated operators on original 1970s and 1980s gates. A lot of Benbrook’s housing stock dates from the late 1960s through early 1990s. The gates are often original, and the operators may be too. Parts for those old units are scarce. We’ll tell you honestly when it’s time to replace rather than patch.
Pricing for Gate Motor & Opener in Benbrook, TX
Here’s what Benbrook homeowners can expect to pay. A standard motor repair runs $240-$520. A new linear arm operator for a residential swing gate starts around $900 installed. Slide motor replacement on a heavy estate or ranch gate runs $1,200-$2,800. Battery backup installation adds $350-$700 depending on the operator type. A full gate motor and opener package with new hardware, safety edges, and a keypad typically lands between $1,800 and $4,500 in Benbrook.
What changes the price most is the gate itself. A 16-foot ornamental iron gate on stable footings is a straightforward job. A 24-foot pipe ranch gate on clay soil that’s been heaving for thirty years is a different project. We quote every job in writing before any work starts, and that price doesn’t change unless you change the scope. Estimates are free. Call (469) 564-8046 and we’ll come measure.
We Also Serve Cities Near Benbrook
Ironworks Gate Co. serves Benbrook and the surrounding communities. If you’re in Burleson, Alvarado, Crowley, or Joshua, our crews are already in your area regularly and can schedule quickly. Same written pricing, same 90-Day Done Right Promise, same live person on the phone.
Serving Benbrook, TX - Our Local Coverage Area
We’re based in the Benbrook area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Benbrook
The answer is almost always soil movement, not the operator. Benbrook sits on expansive clay that swells after heavy rain and shrinks during dry spells. That cycle shifts gate posts a fraction of an inch each season, and the misalignment throws off the limit settings and safety sensors. The fix is stabilizing the footing, not just resetting the operator. Call (469) 564-8046 and we’ll take a look at your specific gate.
Yes, if the system is sized correctly. A solar opener with the right panel and battery bank can run a heavy ranch gate on acreage where running mains power is impractical or expensive. The key is matching the panel wattage and battery capacity to the gate’s cycle count and weight. We’ve installed solar-powered operators on properties throughout the lake corridor and south Benbrook, and they perform well when specced properly. We can assess your gate and give you a written recommendation.
UL 325 requires that automated slide gates have a minimum of two independent entrapment protection devices, typically photo eyes and a reversing edge, plus a secondary safety device like a loop detector or pressure sensor. A wide boat-trailer slide gate near Benbrook Lake must meet the same standard as any other automated gate in Texas. If your gate was installed years ago and never upgraded, it may not be compliant. We can bring it up to code. Call (469) 564-8046 for a free evaluation.
If you replaced the hinge post and the motor still strains, the gate frame itself is likely racked or the gate is too heavy for the operator’s rating. On Benbrook acreage, ranch gates often get reinforced with extra pipe or paneling over the years, which adds weight beyond what the original operator was designed to move. We also check the post footing depth. A new post set in the same unstable clay will move again unless the footing goes deep enough. Our crews dig out and re-pour footings regularly for exactly this reason.
Yes. A battery backup keeps your gate operating during power outages, which matters on Benbrook acreage lots where outages can last hours after storms. Without backup, you’re either manually disengaging the operator or leaving the gate unsecured. Backup systems add $350-$700 to the job depending on the operator. For homes on wells or with livestock, it’s often a necessity, not a luxury. We can install a backup on most brands we service, including DoorKing, Elite, and Ghost Controls units.
Call Ironworks Gate Co. for Gate Motor & Opener Service in Benbrook
If your gate motor is grinding, struggling, or dead, call (469) 564-8046. We’ll answer. We’ll schedule a time that works for you, show up when we say, and give you a written price before any work starts. The 90-Day Done Right Promise covers every job we do in Benbrook, and a live person answers the phone 24 hours a day. Whether it’s a wide lake-area slide gate or an ornamental iron swing gate in an established subdivision, we’re the Gate Motor & Opener company built for Benbrook’s unique ground. Done right, and backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Benbrook since 1984.