Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Kennedale
Gate Installation in Kennedale and welding usually means one thing: a heavy pipe-frame driveway gate that has started dragging, binding, or leaning after the clay soil moved under it. We replace hinge barrels, cut out and rebuild posts, re-true rails, and weld cracked pipe frames back square. Most Kennedale jobs are diagnosed and completed in one visit, with the price agreed to in writing before any work starts. Call (469) 564-8046 and a live person answers, any hour, any day.
Kennedale’s semi-rural layout inside the DFW metroplex means gates here are different from what you see over in Arlington or Fort Worth. These are long, heavy, welded-steel swing gates on caliche drives and acreage parcels. They sit on Blackland Prairie clay that heaves and drops with every rain-drought cycle. When a post tips outward just a couple of degrees, a 16-foot gate drops at the latch side and starts carving a groove into the caliche. That’s the call we get most often in ZIP 76060. We know the fix, and we know how deep to dig so it does not come back next spring.
We’re Ironworks Gate Co.’s Gate Parts & Welding team, and we serve Gate Parts & Welding in Kennedale residents with the same standard we’ve held since 1984: do it right, back it in writing.
Key Takeaways
- Kennedale gate failures are dominated by clay heave tipping posts on heavy pipe-frame swing gates.
- Hinge replacement and post replacement fix most dragging gates without replacing the gate itself.
- Footings on Kennedale acreage need to go 24-30 inches deep to escape the active clay zone.
- Upfront written pricing before work begins. No surprise invoices.
- Every job covered by our written 90-Day Done Right Promise.
Why Ironworks Gate Co. Is Kennedale’s Preferred Gate Parts & Welding Company
We’ve worked on enough Kennedale gates to recognize the pattern before we even get out of the truck. A ranch-style home off Kennedale New Hope Road with a 16-foot pipe gate dragging a 3-inch groove into the caliche. A shared driveway gate near the Mansfield city line where a truck clipped the gate and bent the rack. A horse property where the latch no longer lines up because the post moved an inch over the winter. These aren’t generic gate problems. They’re Kennedale problems, born of this soil and this housing stock. That local familiarity means we bring the right parts, the right welder settings, and the right footing depth on the first trip.
Our technicians are background-checked and uniformed. They work the way they would at their own mother’s house. Victor Salinas, who leads our crew, has spent decades repairing and welding gates across Dallas-Fort Worth, and he drills every tech on the K.E.Y.S. values: Krafted right, Every time, Your home first, Standing behind it. The 400th job gets the same care as the first.
Every completed job is protected by our written 90-Day Done Right Promise. If it isn’t right, we come back and make it right. No paperwork, no arguing, no exceptions. That’s the Keystone Standard on every Kennedale gate we touch.
Our Gate Parts & Welding Services in Kennedale
Hinge Replacement
On a heavy Kennedale pipe-frame gate, the hinge barrels carry the entire load. When the post starts leaning even slightly, the barrel binds, the gate sags, and the latch side drops. In Kennedale’s clay, a hinge that was fine in October can be seized by March. We cut out the old hinge barrels, build up worn post steel with weld, and burn in new barrels while the gate hangs on a temporary support. We verify plumb with a laser before we weld the final pass. The result is a gate that swings free, even on the heavier 14- to 16-foot gates that dominate Kennedale acreage drives.
Post Replacement
Most Kennedale gate dragging isn’t actually a hinge failure. It’s a post problem. A shallow footing, often 18 inches or less, lets the weight of the gate lever the post out of plumb as the clay expands and shrinks. We dig out the old footing, drill down 24 to 30 inches, reset the post in high-early concrete, and brace it while it cures. On a ranch-style property off Kennedale New Hope Road, our tech rebuilt a leaning hinge post for a 16-foot welded pipe swing gate that had carved a 3-inch groove across the caliche drive. We cut out the old 18-inch footing, drilled down 30 inches, reset the post, and rewelded the hinge barrels after checking plumb with a laser. That gate now clears the drive by a clean 2 inches and swings without binding.
Rail Repair
The top and bottom rails on a welded pipe gate do the structural work. When a gate sags and drags on one side, the rails have often racked, twisting the frame out of square. We straighten the frame, weld in gussets where the rail meets the stile, and reinforce the corners so the gate holds its shape. This matters in Kennedale because the long, heavy swing gates common on acreage properties put more torque on the rails than a standard suburban privacy gate ever would. A properly repaired rail means the gate closes true, without lifting or dropping at the latch.
Custom Welding
Not every Kennedale gate repair fits a catalog part. Sometimes the gate was built custom thirty years ago and the hinge barrel, the latch plate, or the rack mount no longer exists in any parts catalog. We fabricate what’s needed on site. We weld cracked pipe, build up worn hinge posts, extend sliding-gate racks, and adapt automation brackets to gates they were never designed to fit. For Kennedale homeowners with horse facilities and pipe-rail perimeter fencing, we also handle the welded gate frame repairs that keep livestock where they belong.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Kennedale
For someone living in Kennedale with an automated gate, the opener brand matters when parts fail. Our techs are factory-trained on nine major Kennedale Gate Motor & Opener lines, including Ghost Controls, DoorKing, Elite, and Mighty Mule. That breadth matters on acreage properties where a solar-powered Ghost Controls board has been baking in 105°F North Texas sun for three summers, or where a DoorKing operator on a shared driveway has lost its travel limits after a rack impact. We carry a broad local parts stock so most Kennedale repairs happen on the first visit, not after a week of waiting for a shipped component. For older Mighty Mule operators and Elite slide-gate boards that are still doing the job, we’ve seen enough failure modes to know the difference between a repairable board and one that needs replacing, usually by the second or third thing we test.
Common Gate Parts & Welding Problems We See in Kennedale Homes
- Clay heave tips the hinge post outward on heavy pipe-frame gates. The post leans just a few degrees, the latch side drops, and the gate starts dragging a groove into the caliche drive. This can happen within one wet season on a gate that was properly installed the year before.
- Shallow DIY footings let the gate’s weight lever the post out of plumb. We regularly see footings under 24 inches on acreage gates. The gate’s weight, combined with expanding clay, shears the weld at the hinge barrel and the whole assembly racks out of square.
- Slide gates on narrow shared driveways bend their rack and pinion. When a truck or trailer clips the gate, the rack bends, the operator trips the safety photocell, and travel limits get lost. The gate then stops mid-travel or refuses to close completely.
- Summer heat accelerates wear on nylon rollers, circuit boards, and solar batteries. Kennedale’s unshaded driveways and 105°F-plus days shorten the life of automation components, especially on rural-style automated gates running on solar-charged battery banks.
Pricing for Gate Parts & Welding in Kennedale, TX
A typical hinge replacement on a Kennedale pipe-frame gate runs $240-$480 depending on gate weight and how much post steel needs rebuilding. Post replacement with a 30-inch footing runs $650-$1,400, which includes digging out the old concrete, new high-early concrete, and setting the post to laser plumb. Rail repair and frame straightening typically runs $200-$500. Custom welding, including on-site fabrication of brackets or hinge barrels, starts around $150 and climbs with complexity and material. For full replacement of a heavy swing gate, expect $1,800-$4,500 depending on length, frame material, and automation.
The price we quote is the price you pay. It’s written down and agreed to before we touch a single bolt. Estimates are free. We also offer a standing $50 discount on any repair over $250, a free second opinion on any written estimate, and a permanent 5% discount for seniors and veterans.
Call (469) 564-8046 for an exact quote on your Kennedale gate.
We Also Serve Cities Near Kennedale
In addition to our daily work in Kennedale, our crews serve Kennedale-adjacent communities including Arlington, Mansfield, Fort Worth, and Burleson. So if you own property on the line between Kennedale and Mansfield, or need gate work on a family member’s place over in Burleson, we’ll be there when we say.
Serving Kennedale, TX - Our Local Coverage Area
We’re based in the Kennedale area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Kennedale
For a heavy pipe-frame swing gate in Kennedale, footings need to go 24 to 30 inches deep. Anything shallower sits in the active clay zone that expands and contracts with every wet-dry cycle, which is exactly what tips posts and drags gates. When we rebuild a post, we drill below that zone and use high-early concrete so the post stays where we set it. Call (469) 564-8046 and we’ll evaluate your current footing depth before quoting the fix.
Nine times out of ten in Kennedale, it’s a post problem. The clay expands through the wet winter, pushes the post outward, and when the ground dries and shrinks the post stays tilted. The gate’s own weight pulls it further out of plumb, dropping the latch side. Hinges get blamed but the hinge usually just follows the post. We’ll verify which it is on site, with a laser and a level, before recommending anything. Estimates are free.
In most cases, yes. We straighten the pipe frame, weld in reinforcement where the rack pulled loose, and remount the rack so the operator’s pinion gear tracks true. The gate only needs replacement if the frame is rusted through or so heavily twisted that straightening would compromise the welds. We’ll show you the damage and explain the math before you decide. Call (469) 564-8046 for a straight answer.
North Texas summer heat, usually combined with a gate that’s working harder than it should. As temperatures climb past 105°F, circuit boards and motors run hotter, and a gate that’s binding or dragging adds enough load to trip the thermal cutoff. The binding is often the real culprit: a wheel track filling with caliche dust, a rack slightly out of alignment, or a post that shifted. We inspect the whole path, not just the operator board. The fix is usually under an hour once the load issue is found.
Yes. We realign the gate first, which usually means correcting the post or the hinge, then we reposition or remount the latch plate to match. In some cases we weld a reinforcing plate on the latch post to give the latch a clean surface. The gate itself is rarely the part that needs replacing. Call (469) 564-8046 and we’ll get it latching correctly again, often in one visit.
Get Your Kennedale Gate Fixed Right
If your gate is dragging, binding, or no longer latching in Kennedale, don’t wait for the next rain cycle to make it worse. We’re a local crew that knows this soil, these gates, and what it takes to make them work. A live person answers the phone 24 hours a day at (469) 564-8046. Estimates are free, the price is written before we start, and every job is covered by the 90-Day Done Right Promise. We’ll be there when we say.
Written by Victor Salinas, Owner at Ironworks Gate Co., leading the Gate Parts & Welding crew serving Kennedale and the surrounding DFW metroplex.