Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Fort Worth
If you’re searching for gate installation in Fort Worth, you probably need a straight answer: a properly engineered driveway gate in this city typically runs $2,400-$6,800 for a single swing gate and $3,800-$9,500 for a sliding gate, with ornamental iron and automation driving the high end. The footing depth matters more than the gate itself here, because Fort Worth sits on Blackland Prairie clay that heaves and sinks with the seasons. We have been setting posts deep enough to survive it for years, and we quote every Fort Worth job in writing before a single bolt is turned. Call (469) 564-8046 and a live person answers, 24 hours a day.
Why Ironworks Gate Co. Is Fort Worth’s Preferred Gate Installation Company
Fort Worth homeowners call us because we understand what this soil does to a gate. The shrink-swell clay under this city does not just crack driveways and foundations. It pushes gate hinge posts up during wet springs and drops them during dry summers, which throws gates out of plumb, makes them drag on concrete, and leaves latches that will not catch. A gate installer who treats Fort Worth like it sits on stable ground will be back in six months fixing what never should have moved in the first place. We set post footings below the active clay zone, sometimes 40 inches deep or more, because that is what this city requires.
Victor Salinas runs every Fort Worth job with the same standard: craft right, every time, no exceptions. You will see background-checked, uniformed technicians on every installation, not a rotating cast of subs. And every completed job carries our written 90-Day Done Right Promise by Ironworks Gate Co. serving Fort Worth. If something is not right, we come back and make it right. No paperwork, no arguing. We also offer a Free Second Opinion on any written estimate you have received, a $50 discount on any repair over $250, an $89 Seasonal Tune-Up, and a permanent 5% discount for seniors and veterans. A live person answers our phone around the clock.
Our Gate Installation Services in Fort Worth
Driveway Gate Installation
Driveway gates are the core of what we do in Fort Worth. We install swing gates, sliding gates, and double gates, plus the full automation package: motors, keypads, loop detectors and access control, photocells, and edge sensors for safety. Fort Worth’s mix of older estate homes and newer HOA communities means we see everything from early-1900s brick pillars to freshly poured concrete columns. Whatever the approach, we engineer the footing for the clay and build the gate to clear without drag through every season. A typical automatic driveway gate in Fort Worth runs $3,200-$7,400 depending on size, material, and opener.
Pedestrian Gate Installation
Pedestrian gates look simple but fail just as often as driveway gates when they are not set correctly. In Fort Worth’s older neighborhoods like Fairmount and Mistletoe Heights, brick columns built in the 1940s and 1950s have cracked along mortar joints from decades of clay-soil movement. If you hang a new pedestrian gate on a shifted column, the latch will not align and the gate will bind. We rebuild the column first with a steel-reinforced core when it is needed, then install the gate so it works smoothly for decades. A standard walk gate installation in Fort Worth starts around $900 and rises with ornamental ironwork.
Swing Gate Installation
Swing gates are the most common choice in Fort Worth, especially for homes with classic ranch or traditional styling. They require more clearance than sliding gates but they look right on older properties and HOA communities that want a traditional appearance. We install single and double swing gates, set the hinge posts deep below active clay, and pair the gate with automation that will not overheat in a Fort Worth August. A single powered swing gate in Fort Worth typically runs $2,400-$5,600 installed, with the operator making up $700-$1,400 of that.
Sliding Gate Installation
Sliding gates work well on Fort Worth properties with short driveways or steep grades where a swing gate would hit the ground or a car. They ride on a track and roller system that must be set level and kept clear of debris. On horse properties that still operate inside Fort Worth and Tarrant County, sliding gates are often the practical choice for wide driveway openings and animal traffic. A motorized sliding gate in Fort Worth generally runs $3,800-$9,500 for a full installation depending on width, material, and access control.
Every Gate Installation job starts with a free measure and a written price. We settle that number before work starts, and it does not move.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Fort Worth
Our technicians are factory-trained on nine major automation brands, including Ghost Controls, DoorKing, Elite, and Mighty Mule. That matters in Fort Worth because HOA communities across the Alliance corridor and homes west of downtown run a mix of everything, and no single brand dominates. When you call us for Gate Repair - Fort Worth, the technician who arrives already knows your opener’s quirks and carries the right parts on the truck. We do not make a second trip for a part that should have been there the first time. If your gate needs a brand we do not usually stock, we order it and schedule the work when it arrives, so you are not waiting on a surprise.
Common Gate Installation Problems We See in Fort Worth Homes
- Heaved hinge posts from Blackland Prairie clay. Fort Worth’s soil expands when wet and contracts when dry, pushing shallow-set posts out of alignment within a year. The fix is a footing below the active clay zone, sometimes 40+ inches deep, not just a hinge adjustment.
- Gates that drag or fail to latch after a wet season. When one post rises and the other sits still, the gate twists and the latch no longer lines up. In neighborhoods like Ryan Place, where original ornamental iron gates from the 1950s are mortared into brick columns, the column itself usually needs rebuilding before the gate can work again.
- Loop detectors that stop triggering the gate. North Fort Worth’s Alliance corridor has a lot of automatic HOA driveway gates with loop detectors buried too shallow. When clay soil shifts, the detector’s field changes and the gate will not open when you pull up. This requires re-cutting and re-setting the loop, not replacing the whole opener.
- Operators failing after weather extremes. Fort Worth summers push heat indices past 110°F, which thermally expands metal and overheats black powder-coated operators baking in full sun. The February 2021 ice storm froze automatic gate operators across the metro and shattered wooden gate boards. We see many of those original 2021-era failures still limping along, waiting for a permanent fix.
HOA Approval: The Step Fort Worth Homeowners Forget
In Fort Worth, especially north of Loop 820 in the Alliance corridor and in established neighborhoods with architectural review committees, the HOA approval often takes longer than the installation itself. Communities with covenants routinely require ornamental iron automatic driveway gates on a specific percentage of lots, and the style, height, and finish must match what the board has already approved. If you buy a gate first and submit the paperwork second, you can end up with an expensive piece of iron that violates the neighborhood’s standards. We coordinate this for our Fort Worth customers. We provide spec sheets with dimensions, material finish, and opener placement, and many boards accept our drawings without back-and-forth because they have seen the quality of our work in their neighborhoods before.
Shared entry systems in gated Fort Worth communities add another layer. When the gate is not just yours but serves multiple homes, the access control must work for every resident, not just the person who paid for it. We install keypads, telephone entry units, and vehicle-mounted remotes through Gate Installation in Fort Worth that integrate with existing management systems, so the property manager and the homeowners both get exactly what they need.
Pricing for Gate Installation in Fort Worth, TX
Here is what new gate installation actually costs in Fort Worth right now:
- Single swing gate, ornamental iron, no automation: $2,400-$4,200
- Single swing gate with LiftMaster or Ghost Controls operator: $3,200-$5,600
- Double swing gate, ornamental iron, with automation: $4,800-$8,200
- Sliding driveway gate, steel or iron, with operator: $3,800-$9,500
- Pedestrian gate, standard steel: $900-$1,700
- Pedestrian gate, ornamental iron matched to existing style: $1,500-$2,800
- Post footing below active clay zone (per post): $350-$700
- Safety photocells and edge sensors (required on automatic gates): $450-$900
Fort Worth pricing runs a little higher than surrounding cities because the clay soil demands deeper footings and because HOA-approved ornamental work often requires custom fabrication. We give you an exact written price after a free measure, before any work is scheduled. You will not get a call halfway through telling you the price went up. Call (469) 564-8046 to schedule that measure.
We Also Serve Cities Near Fort Worth
Our Fort Worth crews regularly work in Kennedale, Arlington, Crowley, and Mansfield. If you live just outside the city line, call us anyway. The same clay soil and the same HOA approval processes apply, and we would rather spend the extra ten minutes on the drive than see another gate fail early.
Serving Fort Worth, TX - Our Local Coverage Area
We’re based in the Fort Worth area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Fort Worth
Yes, the City of Fort Worth requires a permit for any new automatic driveway gate with a motor, including in Fairmount and other historic neighborhoods. The permit covers the electrical connection and the gate’s safety system. We pull the permit for you, schedule the inspection, and make sure the installation passes on the first visit.
We set gate post footings at least 30 inches deep, and on properties with severe clay movement we go 40 to 48 inches to reach below the active shrink-swell zone. This is the single most important factor in whether a Fort Worth gate stays plumb through its first wet season followed by a dry summer. Most failed gates in this city trace back to footings poured at 18-24 inches, which is standard in other markets but not here.
Yes, we match HOA-approved iron styles for homes in the Alliance corridor and across north Fort Worth. Send us your HOA’s approved design packet, or ask your management company to send it. We fabricate to those specifications and submit the spec sheet to your review committee before we order any material. Many Fort Worth HOAs have accepted our drawings for years.
Frozen gate operators usually fail in one of four ways after an ice storm: a stripped gear in the motor, a cracked arm, a damaged control board, or a battery backup that froze and never recovered. The February 2021 event froze automatic gate operators across Fort Worth, and many of those units are still failing intermittently today. We diagnose the exact failure on one visit and replace only what is broken, not the whole system, unless the operator is too far gone to save. We also stock Gate Parts & Welding - Fort Worth for fabricating custom components when needed.
Yes, new automatic gate installations in Fort Worth must include safety photocells or edge sensors that stop and reverse the gate when something is in the way. This is a UL 325 requirement and it is enforced by the city’s permit inspection. We install both photocells and edge sensors on every new automatic gate, even when the city’s minimum allows one or the other. For a free estimate on your gate installation, call (469) 564-8046 today.
Written by Victor Salinas, owner at Ironworks Gate Co., installing and repairing gates across Fort Worth and the surrounding metro.