FAAC Gate Repair Nationwide

FAAC Gate Repair in Burleson: What to Know First

FAAC gate repair in Burleson typically runs between $220 and $680 depending on whether the problem is a control board, a hydraulic pump, or a mechanical failure at the hinge. Most FAAC jobs we see are diagnosed and completed in a single visit, with parts sourced within one to two business days when the damage is more involved. You get an exact price before any work begins, and every repair carries our written 90-Day Done Right Promise.

Call (469) 564-8046

This page is for Burleson homeowners whose FAAC opener has stopped cooperating. Whether it’s an older FAAC 400 Series hydraulic swing gate or a newer FAAC E124 or 770 underground system, we can tell you what’s wrong and what it costs to fix. Call (469) 564-8046 and a live person answers, day or night.

How FAAC Products Fail - and How We Fix Them

FAAC builds a solid operator. But after enough Texas heat and clay-heavy soil, certain failure patterns show up in Burleson driveways more than any other brand. Here’s what we see, in order of frequency:

• E124 and S418 control board capacitor failure. The E124 is a common FAAC board in residential swing gates across Burleson, and its weakest point in this climate is the electrolytic capacitors. Ninty-degree-plus summers bake the board inside the control box, the capacitors dry out, and the gate either stops responding to remotes or opens halfway and quits. We replace the board or repair the capacitor circuit with heat-rated components, then verify voltage under load before we leave.
• 770 and 400 Series hydraulic pump seizing from water intrusion. FAAC hydraulic operators are buried or mounted low, which means they sit in whatever water collects after a Burleson thunderstorm. The reservoir breather lets moisture in over time, the oil emulsifies, and the pump starts laboring or trips the breaker. We drain the old oil, flush the system, replace seals if needed, and refill with the correct FAAC-spec hydraulic fluid.
• C720 and C721 slide gate limit switch drift. On FAAC slide operators in Burleson’s larger properties, the magnetic limit switches slowly lose their calibration. The gate starts stopping six inches short or overrunning the end stop and slamming. We reset and test the limits, then tighten the bracket hardware so it stays put through another season of expansion and contraction.
• Swing gate leaf sag stressing the operator. This one is not technically an FAAC part failure, but it kills more FAAC operators in Burleson than any internal problem. Post-mounted FAAC arms push against a gate leaf that has sagged at the hinge after twenty years in clay soil. The arm works harder every cycle, the motor draws more current, and eventually the board lets go. We fix it properly: rehang or weld the leaf, realign the hinges, and only then address the operator. Fixing the operator without fixing the gate is a temporary patch, and we don’t do temporary patches.
• Photocell and safety edge false trips on FAAC automated systems. Burleson yards get leaf litter, spider webs, and the occasional curious dog. When a FAAC gate reverses for no apparent reason, it’s usually a dirty or misaligned photocell, or a safety edge that has worn through and is grounding out. We clean and realign the eyes, replace worn edges, and test the full safety loop so the gate stops behaving like it has a mind of its own.

Our FAAC Gate Repair Process

Every FAAC job follows the same sequence, whether it’s a failing E124 board or a 770 that won’t lift. We don’t skip steps and we don’t guess.

1. 1
   You call, we answer. A live person takes the call 24/7, asks what the gate is doing, and books a visit. Victor Salinas grew up in Burleson and knows the neighborhoods, so we can usually tell from your street which style of FAAC unit you’re likely running.
2. 2
   We diagnose on site. Our technician checks the operator, the board, the power supply, and the gate hardware itself. We find the actual cause, not just the symptom. Victor’s standing rule applies: “Tell me what it is doing, and I will tell you what it needs - no guesswork, no runaround.”
3. 3
   You get a price before we touch a bolt. We quote the repair, including parts and labor, in writing. You approve it, and the price does not change. No surprises on the bill, ever.
4. 4
   We make the repair. Where FAAC OEM parts are the right call for warranty and compatibility, we use them. Where a quality aftermarket component is genuinely more reliable for a discontinued model, we tell you that too and let you decide.
5. 5
   We test the full cycle. Open, close, stop, reverse, safety edges, photocells, remote range, and the manual release. If we replaced a board, we check the torque settings and limit stops while we’re at it.
6. 6
   We stand behind it. You get the written 90-Day Done Right Promise. If it’s not right, we come back and make it right. No paperwork, no arguing.

What FAAC Gate Repair Costs in Burleson

Here’s what Burleson homeowners can expect to pay for common FAAC repairs. These are honest ranges based on the work we’ve done across this area, not lowball teasers that double after diagnosis.

• FAAC control board repair or replacement: $260-$580, depending on board model and whether we repair the circuit or install new.
• Photocell alignment, cleaning, or replacement: $95-$190.
• Hydraulic oil flush and refill on 400 Series or 770: $220-$360.
• Limit switch calibration and adjustment on C720/C721: $120-$210.
• Hinge realignment and gate leaf rehang before operator work: $280-$700, depending on gate weight and post condition.
• Full diagnostic with no repair: We apply the diagnostic fee toward any repair you approve the same day.

What moves the price: the age of your FAAC unit, whether parts are still in production, and how much mechanical damage sits behind the electrical problem. Estimates are free. Call (469) 564-8046 and we’ll give you a real number before any work starts.

Why Burleson Homeowners Call Ironworks Gate Co. for FAAC Work

We’ve been working on gates in this area for over 42 years, since 1984. That matters because a lot of what fails on a Burleson driveway is the direct result of what the soil and weather have been doing to the gate for twenty years, not just what happened last Tuesday. We know the difference.

We service FAAC alongside eight other major opener brands: LiftMaster, Mighty Mule, Ghost Controls, DoorKing, BFT, Linear, Viking, and Elite. That matters too, because sometimes a homeowner thinks they own a FAAC and the previous contractor actually installed a different board or motor. We recognize what’s actually on the gate and fix that.

Every technician is background-checked and uniformed. Every job gets the written 90-Day Done Right Promise. And every call gets a live person, no matter the hour.

FAQs