BFT Gate Installation Nationwide

BFT Gate Installation in Burleson: What to Know First

BFT gate installation in Burleson typically runs $2,400 to $6,800 for a complete single-swing driveway gate with automation, depending on gate width, post conditions, and whether we’re retrofitting an existing gate or building new. Most BFT jobs are completed in one to two days once materials are on site, and we quote the full price before any work starts. If you’ve got a BFT operator sitting in a box in the garage, or an old BFT motor that’s finally given up, this page tells you exactly what to expect from our crew.

Call (469) 564-8046

As an independent BFT service provider, Ironworks Gate Co. installs, repairs, and replaces BFT automation across Burleson, Joshua, Crowley, and the surrounding Johnson County area. We’re not tied to the manufacturer, which means we can give you the straight answer on whether a part is worth the OEM price or whether a quality aftermarket option will hold up just as well. Call (469) 564-8046 and a live person answers, day or night.

How BFT Products Fail - and How We Fix Them

BFT makes solid Italian automation, but every brand has its habits. Here’s what we actually see on gates in Burleson:

• BFT Deimos series (sliding gates): The limit-switch magnets on the Deimos BT and Deimos Ultra get knocked out of alignment when kids ride bikes past the gate or the wind catches a loose gate panel. The gate starts slamming into the end stops and reversing for no reason. The fix is usually re-leveling the gate, remounting the magnets, and reprogramming the slow-down points. Takes about an hour. Some companies quote a new control board first. We’d rather look at the magnets before we sell you a board.
• BFT Rigel and Phobos (swing gates): These run a worm-gear drive that’s genuinely tough, but the capacitor fails after five to seven years of Texas heat. The gate hums and won’t move, or it moves six inches and quits. A $40 capacitor fixes it. We keep them on the truck. If you call another contractor who doesn’t stock BFT parts, you’ll wait a week while they order one from Dallas.
• BFT Thalia and Kustos (light residential swing arms): On installations where the gate post was never properly set in concrete or has shifted over the years, the arm bracket pulls loose or binds. The operator burns itself out trying to push a gate that’s fighting the hinge line. We re-set or brace the post first, then mount the arm on a flat, square surface. Skip the post work and you’ll be buying a new operator every few years.
• Photo-eye and safety-edge faults: BFT’s wiring terminals are smaller than most American brands, and DIY or handyman installs often leave loose strands touching the chassis. The gate refuses to close, or closes and reopens at random. We trim, re-land, and torque every terminal, then test with obstruction cycles. This is the single most common BFT call we get in Burleson on installs done by someone who “knew a guy.”
• Control board lightning damage: BFT boards are sensitive to surges, and Johnson County gets more than its share of spring storms. We recommend a surge protector on every BFT install, and we hardwire the grounding per the manufacturer’s spec rather than relying on a cheater plug. When a board is genuinely cooked, we’ll quote you both the OEM replacement and a tested equivalent, and tell you which one makes sense for your gate.

Our BFT Gate Installation Process

It starts the same way every time: you call, a person answers, and we schedule a time. We show up when we say we will. Here’s how the job goes from there:

1. 1
   Site walk and honest assessment. We look at the gate, the posts, the existing operator if there is one, the power source, and how the ground drains. Victor Salinas has a way of putting it: “Tell me what it is doing, and I will tell you what it needs - no guesswork, no runaround.”
2. 2
   Written quote, agreed before work. The price is settled before a single bolt is turned. No surprises on the bill, ever. That’s the square deal we’ve run on for over 42 years.
3. 3
   Post and hinge work first. A BFT operator can only be as good as the gate it’s pushing. We repair, re-set, or replace posts and hinges so the gate swings or slides true.
4. 4
   Operator placement and wiring. We mount the BFT unit, run power and low-voltage wiring to code, and set safety edges and photo eyes where Texas law and good sense require them.
5. 5
   Programming and testing. We set travel limits, slow-down points, auto-close timing, and test obstruction reversal at multiple points in the cycle. Then we run the gate through 10 full cycles with you watching.
6. 6
   Cleanup and the 90-Day Done Right Promise. We haul off the old unit, sweep the area, and hand you a written guarantee. If it’s not right, we come back and make it right. No paperwork, no arguing.

What BFT Gate Installation Costs in Burleson

Here are honest ranges for the BFT jobs we do most often in Burleson. Use these as a starting point, not a quote. Your exact price depends on site conditions.

• BFT swing operator on an existing single gate (Thalia or Kustos class): $1,800 to $3,400 installed, including safety edges, photo eyes, and programming.
• BFT sliding operator on an existing slide gate (Deimos class): $2,600 to $4,500 installed, including rack or chain drive, safety devices, and programming.
• Full new swing gate with BFT automation: $4,200 to $7,800 depending on gate size, steel weight, and whether it’s a single or double gate.
• Full new sliding gate with BFT automation: $5,000 to $9,500 depending on track, cantilever, or V-groove design.
• Retrofit of an older BFT to a newer model: $1,500 to $2,800, including removal and disposal of the old unit.

What moves the price: post condition, gate weight, distance from power, and whether we’re dealing with a double gate that needs a synchronization kit. Call (469) 564-8046 for a free estimate. We’ll give you a number you can plan around.

Why Burleson Homeowners Call Ironworks Gate Co. for BFT Work

We’ve been doing gate work in this area since 1984, and we plan to be here another forty years. That means we don’t cut corners that will show up two summers from now. Our technicians are background-checked, uniformed, and trained on BFT as well as LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if your property has a mix of brands, one visit handles all of it. Every job, from a capacitor swap to a full custom gate, is covered by the 90-Day Done Right Promise in writing. And when you call at 9 p.m. on a Sunday because your gate is stuck open and your dog is eyeing the street, a live person still answers. Not a voicemail. Not an answering service. We’ll be there when we say.

FAQs