Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterElite Hinge & Roller Replacement: The Burleson Owner’s Guide
We stock and install Elite-compatible hinge and roller replacement parts daily across Burleson, and most jobs are completed in a single visit. A typical Elite hinge and roller replacement runs $145 to $385 installed, depending on gate weight and how many hinges have worn. You’ll know it’s time when the gate drags at the latch post, squeals on the track, or sits visibly crooked when closed.
The usual discovery goes like this: the opener starts laboring harder than it used to, or a wheel catches on the rail, and one morning the gate simply won’t travel. Nine times out of ten it’s not the motor, it’s the steel that carries the weight. Hinges sag, rollers flatten, and the whole gate falls out of square.
Which Elite Models This Applies To
Elite gate hardware is built heavier than most residential gear, and that’s good news and bad news. The good news is that the hinges and rollers on Elite SL3000 and SL5000 series gates are standardized enough that we can match them from measurements alone. The bad news is that Elite has changed roller shaft diameters between production years, and a part that fits a 2012 Elite won’t always seat in a 2021 model without a bushing.
Before ordering anything, we measure the roller shaft at the bracket, not the wheel face. Elite uses a 5/8-inch shaft on most single-swing gates and steps up to 3/4-inch on double-swing and estate-weight builds. If a homeowner tells me the gate is a double, I already know which end of the tape measure to start with. We recommend OEM Elite hardware when the gate carries an opener load of 400 pounds or more. For lighter manual gates, a quality aftermarket roller with sealed bearings does the job and saves sixty to eighty dollars. Ironworks Gate Co. is an independent service provider, not affiliated with Elite. We simply work on more of them than most shops in Johnson County.
Signs Your Elite Hinge & Roller Replacement Is Failing
- The gate drags at the latch post. The bottom hinge has worn enough to drop the free edge, and the latch no longer lines up without lifting the gate. This only gets worse as the roller compresses.
- A grinding or squealing noise on the track. That’s a roller bearing gone dry and flat. Elite rollers run on a sealed bearing, but Texas dust finds a way in, and once the bearing goes the wheel stops rolling and starts skidding.
- The gate visibly leans when closed. An Elite gate should sit square with an even gap top and bottom. A tilt of half an inch means the top hinge has play, and the bottom roller is carrying weight it wasn’t designed to hold.
- The opener trips its force setting. When the rails bind, the motor works harder and the control board reads that as an obstruction. Homeowners often blame the opener. Usually the opener is healthy and the hinge is done.
- Gray dust or metal shavings at the roller track. That’s either a flat-spotted wheel grinding gone or a hinge pin wallowing out its hole. Both are visible without tools if you know what Burleson driveway grit leaves behind.
Replacement Cost & What’s Included
In Burleson, expect to pay $145 to $385 installed for an Elite hinge and roller replacement. The range covers a single-hinge roller swap on the low end, up to a full set of hinges and both roller assemblies on a heavy double gate. The gate’s weight drives most of the difference, but so does the amount of fabrication needed when an old hinge has hogged out its mounting holes.
| Job | Installed Price in Burleson |
|---|---|
| Single roller replacement (OEM spec) | $145 - $210 |
| Single hinge + roller replacement | $180 - $275 |
| Full hinge set + both rollers (double gate) | $310 - $385 |
Every price is quoted and agreed before we touch a bolt. The quote includes the part, the labor, and any welding needed to true up the mounting points. It also includes the 90-Day Done Right Promise in writing. If something isn’t right after we leave, we come back and make it right, no paperwork, no arguing.
DIY or Call Us?
Replacing an Elite roller on a properly supported gate is within reach for a careful owner with the right wrenches. What is not within reach is a gate that has come off square and put the hinges under load. That steel carries hundreds of pounds, and if it lets go while you’re under it, it doesn’t give a warning. I’ve seen the aftermath, and it is not worth finding out the hard way.
You can safely inspect: check for gray dust at the wheel, look at the gap at the latch post, and listen for grinding as the gate travels. Anything beyond that, call us. We will measure, quote, and have it done before your coffee gets cold. Reach us at (469) 564-8046.
FAQs
Plan on six to nine years for rollers and two to four years longer for hinges, depending on gate weight and how much sand and dust works into the bearings. Burleson’s dry, windy stretches are harder on sealed bearings than people expect.
If the pin and bushing are simply worn, yes, we can machine a new pin and bush it back to tolerance. If the hinge plate has cracked or the mounting holes have wallowed, the hinge is done and replacement is the honest answer. Call (469) 564-8046 and we will tell you which one you have.
A single roller runs thirty to forty-five minutes. A full hinge set on a heavy Elite double gate takes around two hours, including truing up the alignment. Most jobs are one visit, and the price is set before we start.
We carry the most common Elite-spec rollers and hinge sets in the truck, plus fabrication stock for when an existing hinge has left its mounting points in bad shape. For oddball production years we can source OEM parts the same afternoon. We also stock parts for LiftMaster, Mighty Mule, and Ghost Controls gates, but Elite work is what keeps us busy in Burleson.
If your Elite gate is grinding, leaning, or dragging, don’t wait for the opener to take the damage too. Call Ironworks Gate Co. at (469) 564-8046. We will tell you what it is doing, and I will tell you what it needs, no guesswork, no runaround. Victor Salinas and the crew work Burleson every day, and we will be there when we say.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Burleson and nearby areas.