Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterElite Access Control Installation: The Burleson Owner’s Guide
Elite access control installation in Burleson typically runs $485 to $1,240 installed, and we keep the most common Elite-compatible keypads, receivers, and control boards on our trucks so most jobs are finished same-day. The way most Burleson homeowners discover a failed access control unit is unglamorous: the gate ignores the remote at 6:15 on a Tuesday morning, or the keypad lights up but the gate will not move. We service Elite systems across Burleson, Joshua, Crowley, and the surrounding Johnson County area, and this page is the straight answer on what fails, what it costs, and how fast we can have it working again.
Key Takeaways:
- Elite access control installation in Burleson: $485-$1,240 installed, depending on whether we’re replacing a single receiver or a full keypad-plus-board setup
- Same-day service on most Elite access control jobs; we stock common Elite-compatible parts on the truck
- 90-Day Done Right Promise on every job, in writing, no fine print
- Most Elite access control failures are the receiver or the keypad, not the motor itself
Which Elite Models This Applies To
Elite makes gate operators under several series lines, and the access control side varies more than people expect. The Elite SL-3000 and SL-3000UL (the slide-gate workhorses you see all over Parker County and south Fort Worth) use a different receiver protocol than the Elite Swing series on residential driveway gates. If your Elite operator has a separate plug-in receiver board with a small black antenna wire, you have the easier setup to match. If the receiver is integrated into the main control board, we recommend staying closer to OEM Elite parts rather than generic aftermarket receivers, because the handshake between the keypad and the board is proprietary on certain firmware versions.
One compatibility gotcha we see regularly in Burleson: the Elite keypad part numbers that end in “-B” are battery-powered and pair only with the newer receiver boards. The hardwired “-W” versions need a dedicated low-voltage run back to the operator. If you swap one for the other without checking the wiring, the keypad will test fine on the bench and fail the moment it is mounted on the brick column. That is the sort of thing we catch on the first visit because we check the part number, the receiver board revision, and the wiring before we sell you anything.
Ironworks Gate Co. is an independent service provider. We are not affiliated with Elite, but we have worked on Elite operators in Burleson long enough to know which parts interchange and which ones will leave you stranded in the rain with a gate that will not open.
Signs Your Elite Access Control Installation Is Failing
- The keypad beeps but the gate does not move. This almost always points to the receiver rather than the keypad itself. The keypad is transmitting; the receiver board has stopped listening. A new keypad will not fix this.
- Remotes work only within 10 feet of the gate. Elite receiver antennas are small and the receiver module itself degrades over time. In Burleson, where summer heat pushes the control box well past 130 degrees inside, we replace weak receivers more often than any other Elite access control component.
- The gate opens on its own at the same time every day. A ghost signal from a dying keypad or a failing relay on the receiver. Sometimes it is a neighbor’s opener on a close frequency, but more often it is the receiver developing a sticky input.
- You have to punch the keypad code twice before the gate responds. The first press wakes the keypad; the second actually sends the signal. That delay is the keypad’s processor on its way out, not a dead battery.
- The gate closes halfway, reopens, and the keypad flashes an error code. This is typically a safety-edge or photocell issue reporting back through the access control board, but on Elite boards the keypad will sometimes show the fault. It is the board misreporting, not the sensor itself failing.
Replacement Cost & What’s Included
For access control installation on an Elite operator in Burleson, you are looking at these installed ranges:
| Part | Installed Price Range (Burleson) |
|---|---|
| Elite-compatible receiver module (replacement) | $485-$690 |
| Elite-compatible keypad (hardwired or battery) | $540-$780 |
| Full keypad + receiver replacement | $875-$1,240 |
| Access control board (main board swap) | $720-$980 |
The range comes down to two things: whether your Elite unit uses the plug-in receiver (cheaper, faster) or the integrated board, and how the existing wiring holds up. We quote the price before we touch a single wire. The quote includes the part, the labor to install and re-pair every remote and keypad, a full test of the safety sensors and limits, and the written 90-Day Done Right Promise on the whole job. We do not pad the bill with “diagnostic fees” that never get applied to the repair.
DIY or Call Us?
Here is the honest split. If your keypad just needs a fresh battery or you want to re-pair a remote you already have, those are fair homeowner tasks. Elite manuals cover both in plain language, and we will walk you through it over the phone at (469) 564-8046 without charging you a dime.
Where DIY goes wrong on Elite access control is the wiring. The low-voltage runs from the keypad to the operator inside the gate column can carry 12V or 24V depending on the board revision, and landing the wrong wire on the wrong terminal will take out the receiver. High-tension springs on the gate itself are a different conversation entirely, and we tell every homeowner the same thing: a spring under load is not a weekend project. Let a trained tech handle anything that involves the gate’s tension system or the main board. Tell me what it is doing, and I will tell you what it needs - no guesswork, no runaround.
FAQs
An Elite receiver or keypad installed in Burleson typically lasts 8 to 12 years, but the Texas sun shortens that on keypads mounted on west-facing columns. We have replaced keypads on west-facing brick columns in Burleson that looked and acted 10 years old after five, because the direct afternoon heat bakes the keypad’s face and dries out the internal board. A shaded or north-facing mount will give you the full lifespan.
Sometimes, yes. A weak receiver can sometimes be revived by replacing the small capacitor on the receiver board, and a keypad with corroded contacts can be cleaned and resealed. But we only recommend repair when the part is under five years old and the fix will hold. An older Elite unit that is already showing heat stress is a better candidate for replacement, because the repair usually buys you another year, not another ten. Call (469) 564-8046 and we will give you a straight answer on which way to go.
Most Elite access control installations are done in about 90 minutes to two hours on site. A simple receiver swap can be done in under an hour. A full keypad plus receiver job with a board check and re-pairing every remote usually runs two hours, and we do most of them same-day.
We keep common Elite-compatible receivers, keypads, and control boards on our trucks, and we stock deeper parts for Elite operators along with LiftMaster, Mighty Mule, and Ghost Controls at our shop. If we do not have a specific Elite board revision in stock, we can typically have it in hand within one to two business days and get you back on the schedule immediately after.
If your Elite access control is dead on the column and you are tired of keying in the code three times to get your gate to move, call Victor and the team at Ironworks Gate Co. We answer the phone 24 hours a day, we quote the price before we start, and we back every Elite access control installation with our written 90-Day Done Right Promise. Call (469) 564-8046 and we will be there when we say.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Burleson and nearby areas.