Ghost Controls Access Control Installation Nationwide

Ghost Controls Access Control Installation: The Burleson Owner’s Guide

Ghost Controls access control installation in Burleson typically runs $340 to $690 installed, depending on whether you’re adding a keypad, a telephone entry system, or replacing a failed board inside an existing Ghost Controls opener. We stock Ghost Controls-compatible access control parts on our service trucks and complete most installs in a single visit. Most Burleson homeowners discover the problem the hard way: the keypad stops accepting the code, the remote works but the keypad doesn’t, or the gate opens fine but won’t close on a schedule.

Call (469) 564-8046

Ironworks Gate Co. is an independent gate service company, not affiliated with Ghost Controls. That matters because we’re not tied to one brand’s inventory or one manufacturer’s install instructions. We match what’s actually on your gate, wire it right, and stand behind it in writing.

Which Ghost Controls Models This Applies To

Ghost Controls has used a few different access control setups over the years, and the compatibility details trip up a lot of owners. The current lineup, including the AXP1, REX2, and TSS1 series, uses a common accessory port for keypads, push buttons, and vehicle sensors. Older Ghost Controls units from the pre-2017 era ran a slightly different accessory protocol, and that’s the single most common mismatch we see in Burleson: a homeowner buys a current keypad for a ten-year-old opener and it won’t communicate.

The quick way to identify your unit is on the label inside the control-board cover. Ghost Controls prints the model number and a manufacturing date code there. If the date code reads before mid-2017, we verify compatibility before quoting anything, because the wrong accessory will not just fail, it can pull voltage off the board and create a phantom battery drain that kills the whole opener over a few weeks. For Ghost Controls specifically, we stock OEM keypads and aftermarket-compatible entries that are proven on the AXP1 and TSS1 lines. For older units, OEM is usually the only reliable path, and we’ll tell you that honestly before you spend a dollar.

Signs Your Ghost Controls Access Control Installation Is Failing

• The keypad accepts the code intermittently or not at all. The rubber membrane over the keys cracks with sun and heat exposure, and once moisture gets behind it, the traces on the keypad board start corroding. Burleson summers accelerate this dramatically.
• One access device works while another doesn’t. If the remote opens the gate but the keypad is dead, the problem is usually isolated to the keypad’s wiring or its accessory-port connection, not the main control board. That’s a faster and cheaper fix than most owners expect.
• The gate opens on its own or cycles randomly at night. A failing accessory device can send stray voltage back to the control board, which Ghost Controls boards read as a valid open command. We’ve chased this exact gremlin in the Hidden Creek and Mistletoe Hill neighborhoods of Burleson more times than we can count.
• The access control works but has a noticeable lag. Ghost Controls boards are generally quick. A two- or three-second delay between the code entry and the gate moving usually points to wiring resistance building up at a corroded splice or a failing accessory relay.
• The keypad lights up but produces no beep and no gate movement. This points to the keypad’s signal wire or the board’s accessory input rather than the keypad body itself. It’s the kind of diagnosis that takes a meter and about fifteen minutes on site.

Replacement Cost & What’s Included

What a Ghost Controls access control installation costs in Burleson depends on the work involved, and we quote the full number before we turn a single bolt. A straightforward keypad replacement runs $210 to $340 installed, including the part. A full keypad-and-receiver retrofit, which is sometimes necessary on older Ghost Controls units, lands in the $380 to $520 range. Adding a telephone entry system or a card reader pushes toward $690 on the high end because those need their own mounting, power, and programming steps.

Every quote includes the part, the labor, wiring verification with a meter, programming to match your existing remote and board, and our written 90-Day Done Right Promise. The price we quote is the price on the invoice. No exceptions, no surprises, and we settle it before the work starts. Victor Salinas has said it plenty of times: tell me what it is doing, and I will tell you what it needs, no guesswork, no runaround. That applies to the bill too.

DIY or Call Us?

Replacing a Ghost Controls access control part sits on the safer end of gate work. This is not spring tension or a moving gate arm. The real risks are wiring mistakes and compatibility errors, and those are the expensive kind of safe. A reversed accessory-port connection on a Ghost Controls board can short the board itself, and a board replacement on most Ghost Controls openers runs more than the access control part did in the first place. If you’re comfortable with a meter and you have confirmed your model and date code, a keypad swap is a reasonable Saturday project. If there is any doubt about the wiring or the compatibility, that doubt costs more than our service call.

We also stock LiftMaster, Mighty Mule, and DoorKing parts on our trucks, so if the diagnosis turns out to be something else entirely, we’re not leaving you waiting on a second appointment. Call (469) 564-8046 and we will talk through what it’s doing.

FAQs