Ghost Controls Gate Installation Nationwide

Ghost Controls Gate Installation in Burleson: What to Know First

Ghost Controls gate installation in Burleson typically runs $350 to $1,200 for opener installation on an existing gate, and $2,800 to $7,500 for a complete gate-and-opener package. Most Ghost Controls jobs take us half a day to one full day on site, and we schedule them free of charge so you know the exact price before we turn a single wrench. This page is for Burleson homeowners who own Ghost Controls equipment and want a gate specialist who works on this brand every week, not once in a while. If your gate is down right now or you have questions about putting Ghost Controls on a new gate, call (469) 564-8046 and a person answers, day or night.

Call (469) 564-8046

How Ghost Controls Products Fail - and How We Fix Them

Ghost Controls builds dependable openers for the price, but after years of installing and repairing them across Burleson, we’ve learned where they give out first. Here are the failure modes we see most often on Ghost Controls gates in Johnson County.

• AXDP and AXD series arm detaching at the gate bracket. The aluminum arm on the Ghost Controls AXD and AXDP models is light, which is good for easy installs, but the hinge pin at the gate bracket wears oval after a few years of Texas wind loading. The symptom is a gate that opens partway and clunks, or an arm that hangs loose. We re-bush the bracket and re-pin the hinge rather than replacing the whole arm when the motor is still good. That saves a Burleson homeowner about $200 versus a factory arm assembly.
• Rusty limit switch contacts inside the TSS1 and TDS2 openers. Burleson sits on clay soil that holds moisture, and mornings in spring and fall bring heavy dew. Condensation inside the opener housing corrodes the limit switch contacts over time, which makes the gate stop short or run past the stop. Ghost Controls does not sell the limit switch as a field part, so we clean and re-tension the contact assembly rather than telling you the opener is scrap. When the board is gone, we say so.
• Ghost Controls receiver dropping signal from the remote on long driveways. The stock antenna on many Ghost Controls units is a short wire inside a plastic cover. On a Burleson acreage property with a long driveway or a gate set back from the house, that antenna doesn’t reach far enough. We’ve fixed dozens of these by relocating the receiver or adding a simple antenna extension, and most of the time the parts cost less than forty dollars.
• Battery drain on solar-powered Ghost Controls setups. Ghost Controls markets solar kits, and they work well in dry climates. In Burleson, we get stretches of gray skies in winter and late spring storms that block sun for a week at a time. A gate that worked fine all summer goes dead in February because the panel wasn’t sized for our cloud cover. We calculate the real sun-hours for your specific lot and swap in a properly sized panel and battery, not a bigger version of the same undersized kit.
• Misaligned photo eyes on TDS2 and TSS1 after a hard wind event. Burleson gets some genuine north Texas gusts, and a sliding or swing gate flexes in wind more than most homeowners expect. The photo eye brackets Ghost Controls ships are thin stamped steel, and a strong gust can bend one just enough that the gate refuses to close. The fix is usually ten minutes and a bracket reinforcement, but it looks like a dead board to someone who hasn’t seen it before. We have.

Our Ghost Controls Gate Installation Process

Here’s how a Ghost Controls gate installation goes when you call Ironworks Gate Co. in Burleson.

1. 1
   You call (469) 564-8046. A live person answers, asks what the gate is doing, and books a time for one of our techs to come look. Victor Salinas grew up in Burleson and knows these streets, so we aren’t guessing about drive time.
2. 2
   We diagnose the existing setup. We test the motor, the board, the battery or power supply, the safety edges, and the gate hardware itself. A Ghost Controls opener on a rusted, sagging gate will fail again no matter how good the motor is, so we look at the whole system.
3. 3
   We give you a written price before any work starts. Not a ballpark, not an estimate that changes later. The number we quote is the number you pay. If we find something mid-job, we stop and talk to you first.
4. 4
   We install or replace the Ghost Controls opener. We use Ghost Controls OEM parts where they matter most, like control boards and receiver modules, but we’ll use a quality aftermarket part when it does the same job better for less, like battery cables or mounting brackets. We’ll tell you which is which and why.
5. 5
   We test the gate through every cycle. Open, close, stop, auto-close, safety reverse, manual release. If it doesn’t pass, it doesn’t get called done.
6. 6
   You get the 90-Day Done Right Promise in writing. If anything isn’t right within 90 days, we come back and fix it. No paperwork, no arguing.

What Ghost Controls Gate Installation Costs in Burleson

Here are honest price ranges for the Ghost Controls scenarios we handle most often in Burleson. Every price below includes labor and the parts described.

• Opener install on existing single swing gate: $350 to $700, depending on whether we need to run new wire and how far the gate is from a power source.
• Opener install on a double swing gate (dual operators): $850 to $1,200, more if the gate posts need reinforcement.
• Replace an older Ghost Controls opener with a new unit: $500 to $900, including removing the old motor and mounting the new one.
• Complete new gate and Ghost Controls opener package: $2,800 to $7,500, depending on gate size, material, and whether you need a keypad or intercom.

What moves the price most is the condition of the gate itself and the power situation. A gate that’s square and solid with a nearby outlet is a simple job. A sagging gate with no nearby power and a long wire run is a different afternoon. We’ll tell you exactly what you’re looking at during the free estimate. Call (469) 564-8046 and we’ll put a number on paper for you, no obligation.

Why Burleson Homeowners Call Ironworks Gate Co. for Ghost Controls Work

We’re an independent Ghost Controls service provider, not a factory warranty shop, and we’ve been doing gate work in Burleson for over 42 years. We work on Ghost Controls openers every month, which means our techs know this brand’s quirks the way a mechanic knows a certain pickup. And when a Ghost Controls unit is truly dead and the right call is something else, we can put in a LiftMaster, Mighty Mule, or DoorKing opener from our stock, because we carry and service all of them. Victor Salinas has been pulling wire and welding gates around this town since before most of the new subdivisions went in, and he built this company on one rule: tell the homeowner what’s wrong, quote a fair price, and stand behind the work. Every job gets the 90-Day Done Right Promise, and every call gets a live person, not a voicemail.

FAQs