Viking Gate Parts & Welding Nationwide

Viking Gate Parts & Welding in Burleson: What to Know First

Viking gate parts and welding in Burleson is work we handle every week at Ironworks Gate Co., from hinge replacements and post repairs to custom reinforcement welding that makes an old Viking gate close like it did the day it was hung. Most Viking parts jobs run $180 to $650 depending on what failed, and we quote the price before we turn a single bolt. If you own a Viking gate that’s sagging, stuck, or shedding metal, call (469) 564-8046 and we’ll tell you what it needs.

Call (469) 564-8046

This page is for Burleson homeowners who own a Viking gate system and want straight answers about parts, welding, and what it costs to fix it right. We’re an independent Viking service provider, not a factory warranty center, which means we fix what’s actually wrong rather than selling you a parts kit you don’t need.

How Viking Products Fail - and How We Fix Them

Viking gates are common in Burleson’s older subdivisions and acreage properties, and after years of working on them, we know exactly where they give up first. Here are the failure modes we see most:

• Sagging hinge posts on Viking R-6 and G-5 series gates. These are heavy steel gates, and once the post base starts moving in North Texas clay soil, the hinge side drops and the gate drags. We weld in a new post base or sleeve the existing post and re-hang the gate so it swings true again.
• Cracked rail welds on the Viking G-5. The mid-rail on this model carries a lot of load, and at the hinge stile the factory weld is often the first thing to fatigue. We grind out the crack and lay a full-penetration weld, then add a gusset plate so it doesn’t come back.
• Worn gate rollers on Viking slide gates. Burleson’s fine caliche dust works into the roller bearings and grinds them down. When the gate starts chattering mid-travel, that’s roller wear, not a motor problem. We replace the rollers and adjust the track rather than selling you an opener you don’t need.
• Latch and lock failures on Viking G-3 pedestrian gates. The latch striker on these lighter gates gets bent when the gate is forced open against the wind, and then the mag lock won’t seat. We straighten or weld in a fresh striker and re-align the lock so the gate actually stays closed.
• Hinge barrel cracks on older Viking R-series. The cast hinge barrels on early 2000s units weren’t designed for forty years of Texas sun and wind. The barrel splits, the gate leans, and the whole weight lands on the lock side. We weld in a heavier barrel hinge assembly, which usually outlasts the rest of the gate.

Our Viking Gate Parts & Welding Process

When you call us about a Viking gate in Burleson, here’s how the job goes:

1. 1
   You call, a person answers. Not a voicemail tree. We ask what the gate is doing, and we’ll tell you over the phone whether it sounds like a hinge problem, a weld problem, or something in the opener.
2. 2
   We come out and look at the gate. We measure the post drop, check the hinge wear, run the gate through its travel, and look for cracks that the paint has hidden.
3. 3
   We give you a written price before any work starts. You know the number, and that’s the number on the bill. No surprises after the fact.
4. 4
   We fix it with the right parts. For hinge and structural work, we typically weld in heavier steel than the factory used. For moving parts like rollers and latches, we use OEM Viking where it matters and quality aftermarket where it’s just as good and costs less. We’ll tell you which is which.
5. 5
   We test the gate under load. We run it thirty or forty times, open it against the wind, and make sure it stops, starts, and seats correctly with weight on it.
6. 6
   We clean up and stand behind it. Every Viking parts and welding job is covered by our written 90-Day Done Right Promise. If it’s not right, we come back and make it right. No arguing, no paperwork.

What Viking Gate Parts & Welding Costs in Burleson

Here’s what Burleson homeowners can expect to pay for the most common Viking parts and welding work we do:

• Hinge replacement (single hinge, welded): $180-$320
• Hinge replacement (full gate, both hinges): $320-$550
• Post replacement with new base welded in: $400-$800
• Cracked weld repair with gusset plate: $150-$350 per repair
• Gate roller replacement (slide gate, pair): $180-$280
• Latch and striker repair, re-aligned: $120-$250
• Full custom welding (reinforcement, gate extension, frame repair): $85-$110 per hour plus steel

The price moves based on how heavy the gate is, how deep the post is set, and whether we’re working around an opener that has to be disconnected and re-aligned. We quote it up front, in writing, before any work begins. If you have a written estimate from someone else, bring it in for a Free Second Opinion. And if your repair runs over $250, ask about the $50 off. Call (469) 564-8046 for a free estimate on your Viking gate.

Why Burleson Homeowners Call Ironworks Gate Co. for Viking Work

We’re not the company that installs a gate and disappears. We’re the company that still answers the phone when a Viking gate that’s twenty years old finally gives up. Our technicians are background-checked and uniformed, and they know Viking gates well enough to tell you whether the problem is the hinge or the motor before they unload the truck. Victor Salinas, our owner, grew up in Burleson near the old Chisholm Trail Crossing area, and he’s been working on gates like yours for over two decades.

And while Viking is a brand we know deeply, we’re also trained and equipped on LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if your gate has a Viking frame but someone put a different opener on it, we can fix both halves in one visit. Every job, Viking or otherwise, carries our written 90-Day Done Right Promise. If it’s not right, we make it right.

FAQs

Call Ironworks Gate Co. for Viking Gate Parts & Welding in Burleson

If your Viking gate is sagging, dragging, or held together by rust and good intentions, call (469) 564-8046. We’ll come out, tell you what it needs, and give you a written price before any work starts. Victor Salinas says it best: “Tell me what it is doing, and I will tell you what it needs - no guesswork, no runaround.” That’s how we’ve done it in Burleson for over 40 years, and that’s how we’ll do it on your gate.

Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Burleson and nearby areas.