Linear Hinge & Roller Replacement Nationwide

Linear Hinge & Roller Replacement: The Burleson Owner’s Guide

Linear hinge and roller replacement in Burleson typically runs $185 to $465 installed, depending on the gate’s weight, the number of hinges, and whether the rollers are standard nylon or heavy-duty steel. We stock Linear-compatible hinges and rollers on our trucks and can usually complete the swap the same day we arrive. Most owners discover the problem the same way: the gate starts dragging on the ground, or it makes a grinding sound every time it opens, or it simply refuses to close flush anymore. That is the hinge or roller telling you it has given up. The good news is this is a repair we do regularly, and when it is done right, your Linear opener stops working overtime and the gate swings like it did years ago.

Call (469) 564-8046

Which Linear Models This Applies To

Linear has manufactured swing gate openers under a few different series names over the years, and the hinge and roller hardware varies between them. The most common in Burleson are the Linear LRA and LS series swing gate operators, along with the older Access Pro and GTO-era gates that Linear absorbed. The hinge side of the equation is fairly universal: the gate post mounts typically use a 1-1/2-inch or 2-inch barrel hinge with either a greasable zerk fitting or a sealed bearing. The roller side is where compatibility gets specific. Linear gates with a cantilever or rolling design use a 4-inch or 5-inch nylon roller with a 3/4-inch axle, while heavier custom gates may call for a 6-inch steel roller rated for 1,500 pounds or more.

Here is the gotcha we see often in Burleson: a homeowner buys a generic “gate roller” off a shelf, bolts it on, and wonders why the gate still binds. Linear’s heavier operators are designed around a specific roller diameter and offset, and changing that geometry by even half an inch alters how the gate tracks through its arc. We recommend matching the original part number when possible. Linear OEM hinges and rollers are good hardware, but for gates older than ten or fifteen years, a quality aftermarket replacement from a brand like National Hardware or a machined steel equivalent can often outlast what Linear originally supplied. We will tell you honestly which one makes sense for your gate and your opener.

Ironworks Gate Co. is an independent gate service company, not affiliated with Linear or its parent company. We service and replace Linear hardware because it is common on Burleson driveways, and we keep the right parts on hand.

Signs Your Linear Hinge & Roller Replacement Is Failing

• The gate sags at the latch end. This is the classic hinge problem. The top hinge has worn or the post has shifted, and the weight of the gate is now pulling downward instead of hanging square. Your Linear opener is working harder to compensate, which shortens its lifespan.
• The gate scrapes the driveway in one spot. A worn roller has lost its round profile or its bearing has seized, so it grinds flat on one side instead of rolling. You will see a semicircular scrape mark in the concrete as the evidence.
• A grinding or squealing noise when the gate moves. Bearings in rollers and hinges are sealed at the factory, but years of Texas heat and fine Burleson clay dust work their way past the seals. Once the bearing runs dry, metal grinds on metal.
• The gate jerks or hesitates mid-travel. The Linear opener is trying to push through resistance from a bad roller or a hinge that is binding. The opener’s torque limiter is doing its job, but that jerking motion is the gate fighting the hardware.
• Visible rust bleed or cracking around the hinge leaf. This is the one we take most seriously. A rusted hinge can fail suddenly, and a 300-pound gate swinging free is not a risk anyone in Burleson should carry. If you see rust on a hinge, call us before it becomes a call about a gate on the ground.

Replacement Cost & What’s Included

For a standard single swing gate in Burleson, replacing both hinges and one roller typically falls between $185 and $320 installed. A heavier gate with two rollers and three hinges, or a gate that needs steel rollers instead of nylon, runs $340 to $465. The price includes removal of the old hardware, installation of the new hinges and rollers, greasing all fittings, and a realignment check so the gate travels through its full arc without binding. On gates where the post itself has shifted, we may need to weld a new hinge plate or reset the post, which adds to the total. That is rare, but we will tell you before we touch anything.

Every price is quoted and agreed before work starts. No surprise line items, no invoice that looks different from the quote you approved. The work is covered by our 90-Day Done Right Promise: if something is not right, we come back and make it right. In writing, no arguing.

DIY or Call Us?

There are two things you can safely check yourself before calling. First, look at the roller and see whether it spins freely or has worn flat. Second, open the gate and watch the hinge barrels to see if the gate drops when it is at full swing. That tells us what we are dealing with. But here is where DIY goes wrong: a gate under tension is dangerous. The Linear opener is holding the gate in position, and when you unbolt a hinge or a roller, the gate’s full weight can shift in a fraction of a second. We have seen crushed fingers and broken gate arms from what started as a simple parts swap. The other issue is buying the wrong part online. We stock the correct Linear-compatible hardware on the truck, matched to your gate’s weight and your opener’s geometry. It is the difference between one visit and two.

If your gate is sagging, grinding, or scraping, call us at (469) 564-8046. We will tell you what it is doing, and we will tell you what it needs. No guesswork, no runaround.

FAQs