FAAC Gate Access Control Nationwide

FAAC Gate Access Control in Burleson: What to Know First

FAAC gate access control repair in Burleson typically runs $225-$480 for most keypad, receiver, and board issues, and we complete the large majority of FAAC jobs in a single visit. We are an independent FAAC service provider, not a factory-authorized dealer, which means we make repair decisions based on what actually gets your gate working again, not on what protects a manufacturer rebate.

Call (469) 564-8046

If you are standing at a FAAC keypad that will not accept your code, or a gate that opens for the remote but not the phone app, this page tells you what is really going on and what it costs to fix it. Victor Salinas and the Ironworks Gate Co. team serve homeowners throughout Burleson, from the older neighborhoods near Old Town to the acreage properties south of 1187. Call (469) 564-8046 and a live person answers. Not a voicemail, not a phone tree. A person.

How FAAC Products Fail - and How We Fix Them

FAAC builds solid machines. The hydraulic 400-series operators and the electromechanical 770 and 390 models are common on Burleson driveways, and they fail in predictable ways. Here is what we see on access control specifically:

• FAAC E024U and E124 control boards stop recognizing keypad and receiver inputs after hard power blinks. Burleson spring storms knock out power regularly. When power returns in a sag or surge, the FAAC board’s input terminals can lock the gate in “close” and ignore all wired accessories. The fix is a board re-learn and input re-initialization, which takes about an hour. We do not replace a board until we have proven it cannot be re-learned.
• Photobeam faults shut down FAAC gates and blame the access system that did nothing wrong. The single most misdiagnosed FAAC symptom in Burleson is a gate that will not close because the FAAC board sees a false obstruction signal. The owner thinks the keypad or the remote died. It is almost always a misaligned or sun-blinded photobeam, and on west-facing Burleson gates the late afternoon sun triggers it every day. We realign and shield the beam before touching a single access component.
• DSL and KP keypads refuse codes after a lightning strike nearby, even when the keypad looks fine. The FAAC KP keypad’s EEPROM is vulnerable to induced voltage on buried wire. We see this on long runs from the house to the driveway gate, especially where the wire shares a trench with landscape lighting. We isolate the keypad circuit, test the wire, and replace only what the surge actually killed.
• FAAC 433MHz receivers drop the signal from remotes that worked for a decade. Older FAAC RP receivers are single-frequency units, and they gradually drift. The remote “works” at five feet and dies at fifty. This is the classic FAAC access control failure on larger Burleson lots where the house sits well back from the gate. We test signal strength at the actual operating distance and replace the receiver with a matched FAAC unit, or move to a newer dual-frequency receiver when the old one is past its useful life.
• Phone entry and smart access retrofit jobs run into FAAC’s dry-contact input quirks. FAAC boards do not always accept a simple dry contact from a third-party phone entry or smart controller the way LiftMaster or BFT boards do. Some FAAC inputs are looking for a voltage edge, not a contact closure. We know which FAAC input terminal to land the wire on and which settings to change, because we have been doing FAAC retrofits on Burleson gates for years. This is the single most common reason a “universal” phone entry kit never works on a FAAC gate.

Our FAAC Gate Access Control Process

When you call about FAAC gate access control in Burleson, here is how the visit goes, start to finish:

1. 1
   You talk to us first. You call (469) 564-8046 and tell us what the gate is doing. We ask plain questions: Which keypad do you have? Does the remote still work? Does the gate close on its own when the sun is low? The answers tell us which parts to bring.
2. 2
   We arrive with the right test equipment and the right parts. We do not do FAAC jobs out of a truck that is guessing. We carry FAAC board test leads, signal meters, and the common FAAC parts that usually fail: receivers, keypads, photobeam sets, and the capacitors that age out on older 400-series boards.
3. 3
   We verify the failure before we touch anything. Every diagnosis is confirmed with a meter or a reproducible test. No parts get replaced on a hunch. On FAAC access control, that means testing the actual input terminal on the board, not just assuming the keypad is bad because it acts dead.
4. 4
   We price the job in front of you, before the work starts. The price is the price. We decide together whether the part should be FAAC OEM or a quality aftermarket equivalent, and we tell you the difference in cost and lifespan for your specific model. You are not getting a bill you did not agree to.
5. 5
   We make the fix and test it the way you use it. Keypads get tested from the driver’s seat. Remotes get tested at the actual distance from the house. Photobeams get tested with the sun in the wrong place, if that is what your gate faces.
6. 6
   We stand behind it in writing. Every FAAC access control job leaves with our 90-Day Done Right Promise. If it is not right, we come back. No paperwork, no arguing.

What FAAC Gate Access Control Costs in Burleson

Here are honest ranges for the FAAC access control work we do most often on Burleson gates:

• FAAC keypad replacement or reprogramming: $225-$380, depending on whether the existing keypad can be salvaged and whether we are running new wire
• FAAC receiver repair or replacement: $260-$420, including testing at operating distance and matching the new receiver to your existing remotes
• Photobeam realignment or replacement pair: $180-$340, including sun shield installation where the west-facing afternoon glare is the problem
• Phone entry or smart access retrofit on a FAAC board: $480-$850, depending on the controller chosen and how much wire needs to be pulled
• Full FAAC control board replacement: $550-$900, including board programming and input configuration for all existing accessories

The price moves based on the age of the FAAC product, the wire runs involved, and whether we are matching legacy FAAC components or replacing them with current parts. Every quote is agreed before work begins. Call (469) 564-8046 for a free estimate on your specific FAAC setup.

Why Burleson Homeowners Call Ironworks Gate Co. for FAAC Work

We have been working on driveway gates in this area for over 42 years, founded in 1984, and FAAC has been on our service list for most of that time. Our technicians are background-checked and uniformed, and they work in your driveway the way they would work in their own mother’s. The 90-Day Done Right Promise is written on every invoice we hand you. If the FAAC access control fix is not right, we return and make it right without a fight.

And when a FAAC system is not worth repairing, we do not have to hand you to a stranger. We service eight other gate automation brands on the same visit: LiftMaster, Mighty Mule, Ghost Controls, DoorKing, BFT, Linear, Viking, and Elite. If the right answer for your Burleson gate is a different opener, we will tell you that plainly and give you a written price for the change.

FAQs